3D printer 1.75mm filament end / runout Detector - Monitor - Sensor - Buzzer - Alarm

3D printer 1.75mm filament end / runout Detector
Monitor - Sensor - Buzzer - Alarm
The best gadget for your 3D Printer!

This filament runout detector / buzzer can used with any printer which uses 1.75mm filament. I am old 3d printer user and designed very carefully having in my mind every needed detail and every problem that could be happen.No need electronics knowledge to use it. It is very simple.
To operate device, first you need put a 12V, 23A battery (like one for car alarms).
You insert the filament in the hole (on the way of the arrow) and after that to the filament feeder of your 3D printer. Do not forget to open the switch.

There is a switch, in which you must change position to the right to be ON. Switch is protected in a case that device fell down. To the other side there is a hole, which you can use it to tie the device on the printer (not very close to the feeder, to have more time after alarm). Also, you can use a double side tape, to put it on the 3D printer.
At the top, there is a plastic protrude, to avoid in a case device fall upside down mute the buzzer and not hear it from long distance.
When filament runout, you will hear a very loud beep. After that, close the switch on the detector, pause printing, move up the head, remove the remaining filament and repeat the above procedure to put the new. Press to continue printing.

You can purchase device with or without battery included. Choose from the list.

I suggest you, first time make a test to confirm in which distance you hear it. If after long time of use you do not hear it well, change the battery.
Device is hand assembled and fully tested prior shipment.

Notice: Device builded with 3D printer using ABS filament. Good quality but not perfect like molded plastic. Please see gallery photos at the top for more detailed view. Device color is random. Battery is alkaline, not necessary the same brand or model as in photos, but same type.

To order, follow the LINK.

Photoduino + Object Splash Water Photography Device + Mariotte Siphon with solenoid valve

PHOTODUINO PCB ASSEMBLED with Arduino board, Sensors and Case

+

Object Splash Water Photography Device / DropShot - Drop Box - Camera

+

Mariotte Siphon with solenoid valve for water drop photography

Cheaper compared with ANY other solution with same or even less capabilities

Buy a complete set of all above devices and

SAVE A LOT OF MONEY!

Photoduino is an open source camera controller based on the Arduino platform which you can use to automatically take pictures with your DSLR camera.
Its main purpose is to serve as technical support for shooting high speed photos, but you can use as intervalometer to make  ”Timelapse” videos or for animals or insects photography. Check the example photos.

For any help and more detailed info about photoduino use this LINK. 

Please check all listings that included to this offer, clicking on each one, to read more details.

Mariotte Siphon with solenoid valve for water drop photography

Mariotte’s bottle is a device that delivers a constant rate of flow from closed bottles (or tanks). We use it in water drop photography to keep the flow rate stable.
Mariotte bottle (also called "Mariotte siphon") is the best choice to use in water drop - splash photography because keeps the drop size same until liquid is to the lower level of the tube inside bottle.
The devise is designed especially for photography and includes a Mariotte bottle and a 12V solenoid valve.
Some parts, as you can see, designed and printed with 3D printer using ABS plastic. Not same finish like molded, but good quality and no problem with operation.
The bottle is big (200ml) and can release hundreds drops until needed to refill it.
This device can used in a place of any other which uses 12V for controlling solenoid. 

Device is available for sale at this LINK.

Object Splash Water Photography Device / DropShot - Drop Box

 

Device can used in the place of any 12V solenoid valve for water drop photography

Designed for this specific use and it is very easy to operate it. The only needed is to solder it to the proper connector or terminal block on your drop controller.

Also, you need a lab retort (about 50cm high) which maybe you have it already (if you own a device for water drop photography) or a cheap engineer's vice to hold it.

If use a retort, then use the worm screw to tight device on the rob. Do not screw it more than needed to be stable and try be the worm screw to same angle-position like you see on photos.

The two doors at the bottom, have a line on it and when device is ready for use you can see a cross, which helps you center the object.

NOTICE: Device made using 3D printer. Not perfect shape, but good quality, enough to hold heavy objects, like a big tool battery. But do not try to test their limits. Not designed for very heavy objects.

Interface is hand assembled and fully tested prior shipment.

Connector, device, cable, etc, color can change.

If it is out of stock, please check again after some days. To be 3D printed and assembled, needed about 5 hours. In a case of many orders, time is not enough to replace the stock.

 

If you do not own a device, you can buy a Photoduino controller. If you order the device and an assembled Photoduino controller or set, then you will pay only the shipping cost for photoduino. The shipping cost for this device, will be full refunded. To see available options of Photoduino use this LINK. 

Device is available for sale at this LINK.

Yaesu Digi Interface with PTT - PSK,PSK31,RTTY,SSTV,. for FT-920, FT-1000, FT-1000D, FT-1000MP, FT-1000MPMKV, FT-1000MPMKV-Field, FT-2000, FTDX-5000/D/MP, FTDX-9000/D/MP

YAESU USB Digital Interface with PTT control
PSK31, PSK, RTTY, SSTV, NBEMS, JT-65, WeatherFax and other digimodes
HF/VHF/UHF(Hardware version 5)

Compatible with Yaesu transceivers Models FT-920, FT-1000, FT-1000D, FT-1000MP, FT-1000MPMKV, FT-1000MPMKV-Field, FT-2000, FTDX-5000/D/MP, FTDX-9000/D/MP (transceivers not included) and all other models with 5 pin DIN Data/Packet port (with same pin assignment). This interface allows your PC or Laptop, to decode/encode digital signals using free (or paid) software.

3 in 1 - BEST VALUE FOR MONEY
USB audio interface + Digital Interface + PTT control
*** sold tens of them ***

• No need to use your PC, Laptop or Netbook soundcard 
• No need to use internal or USB serial port.
  
• No need to plug and unplug your mic & speakers. Just connect it to a free USB port
• No need for drivers
• PnP with Windows XP, Vista, 7, 8 and all OS that support generic audio interface
• Supports FLDIGI, MMSSTV, DIGIPAN, MultiPSK and any other program that can send PTT tone to right audio channel or play the digital signal to both audio channels
  
• You can download software clicking HERE

Why pay more for less? Pay less for more!

HOW TO:

• Connect USB Interface to a free USB port (OS will detect it and install drivers). If not, try other USB port or connect it alone if you use USB hab.
• Open your application and configure it to use the proper audio device and select audio mono output or PTT tone to right audio channel. If you can't find such options, probably application sends signal to both audio channels (no problem).
• Tune your radio to a digi mode frequency.
• Open USB Audio properties, adjust audio output and MIC level tho the highest level. If it is necessary, disable Mic AGC.
• Plug 5 pin DIN connector to Data/Packet port.
• Tune your radio to a digimode frequency.
• Use green potentiometer to adjust audio until you have the proper receiving (RX) level.
• Use red potentiometer to adjust transmitting (TX) level (check ALC level). When transmits, red led turns on.

Interface is assembled and tested.
Total interface length with cable is ~1m. Cable, box or jack color could vary.
USB cable not included.
Dimensions: 6.5x8.7x2.6cm (2.56x3.42x1.02in)
Notice: Box is custom designed and build with 3D printer. Good quality but not perfect like molded boxes. Please see gallery photos at the top for more detailed view.
Before you order, please read carefully the item's description. Check your radio manual to confirm that is compatible and how to set the correct settings.

• Ship to confirmed addresses.
• First priority shipping next business day with tracking number (You can check shipping date from purchase history).
• Shipping and handling charges covers the real cost for first priority registered post. Shipping with a courier, will be extremely expensive
• Normally delivered within 5-15 business days after shipping. If you want it very fast, I can not guarantee it, but it will not be unusual, if you receive it in less than 5 days.
• Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast. Also, some countries does not update tracking history, until they deliver the packet.
• 
  
• I suggest you to use 17track to track your order. If its necessary, choose your destination country.

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.

Check out my other items. Add me to your favorites list.

Photoduino assembled PCB Arduino digital camera shield 3.0 **** Complete **** Time Lapse, Arduino shield,trigger audio,vibration,laser, etc

PHOTODUINO PCB ASSEMBLED with Arduino UNO board and covers

Photoduino is an open source camera controller based on the Arduino platform which you can use to automatically take pictures with your DSLR camera.
Its main purpose is to serve as technical support for shooting high speed photos, but you can use as intervalometer to make  ”Timelapse” videos or for animals or insects photography. Check the example photos. It is an electronic circuit that is placed on an Arduino board as a “shield” taking all inputs, outputs and power pins. It has all the necessary electronic components and connectors for connecting the camera, flashes and sensors.
You can control the shutter and camera autofocus and also can triggering of two flashes. It also has a sound sensor, an shock/impact sensor and a laser or infrared barrier that can be used to take pictures when you register an event in the sensor. With the Solenoid Valve Interface you can generate droplets directly from Photoduino.
The configuration is done entirely through a small LCD screen using only two buttons, so it works independently without the need for a computer (except for firmware updates) but also, you can use the Photoduino Remote Software to wide control Photoduino from your computer.
Top and bottom cover is clear acrylic sheet, spacers are ABS 3D printed, which also protect acrylic at the corners.

NOTICE:

• I sell the main PCB (and solenoid valve circuit), assembled with Arduino UNO board.
• Sensors, not included.
• I use BT169D thyristors.
• USB cable not included.
• Arduino board USB connector is type "B", but in case of no availability, can be "micro USB".
• I suggest you to use an "external power bank battery charger" to power the device. It lasts for long time, it is rechargeable and cheap.

PCB design modified by me, to be able use more common components, like speaker and contrast trimmer.
Also, changed pcb traces to include the solenoid control board.
For any help to build it and for needed components, you can find instructions to this Link to build it.

Ship to confirmed addresses

First priority shipping next business day with tracking number (You can check shipping date from purchase history).

Shipping and handling charges covers the real cost for first priority registered post

Normally delivered within 3-7 business days after shipping

I suggest you to use 17track to track your order. If its necessary, choose your destination country.

Before you sign  to receive your order, check the package for damage. For more info, click this Ebay LINK.

Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast.

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.

Alinco DX-77 Digi Interface with PTT - PSK,PSK31,RTTY,SSTV

ALINCO USB Digital Interface with PTT control
PSK31, PSK, RTTY, SSTV, NBEMS, JT-65, WeatherFax, Echolink and other digimodes
HF/VHF/UHF

Compatible with ALINCO DX-77 and variations of this model (transceiver not included) and all other radios with same 8 pin ROUND connector and pin assignment as shown to the picture gallery. NOTICE: Check your manual to be sure that MIC connector supports to pin 6 AF (Audio) output. This interface allows your PC or Laptop, to decode/encode digital signals using free (or paid) software.

3 in 1 - BEST VALUE FOR MONEY
USB audio interface + Digital Interface + PTT control
*** sold tens of them ***

• No need to use your PC, Laptop or Netbook soundcard 
• No need to use internal or USB serial port.
  
• No need to plug and unplug your mic & speakers. Just connect it to a free USB port
• No need for drivers
• PnP with Windows XP, Vista, 7, 8 and all OS that support generic audio interface
• Supports FLDIGI, MMSSTV, DIGIPAN, MultiPSK and any other program that can send PTT tone to right audio channel or play the digital signal to both audio channels
  
• You can download software clicking HERE

Why pay more for less? Pay less for more!

HOW TO:

• Connect USB Interface to a free USB port (OS will detect it and install drivers)
• Open your application and configure it to use the proper audio device and select audio mono output or PTT tone to right audio channel. If you can't find such options, probably application sends signal to both audio channels.
• Tune your radio to a digi mode frequency
• Open USB Audio properties, adjust audio output and MIC level tho the highest level. If it is necessary, disable Mic AGC.
• Plug 6 pin mini-din to Kenwood Data port
• Tune your radio to a digimode frequency.
• Use green potentiometer to adjust audio until you have the proper receiving (RX) level.
• Use red potentiometer to adjust transmitting (TX) level (check ALC level). When transmits, red led turns on.
 

Interface is assembled and tested.
Total interface length with cable is ~1m. Cable, box or jack color could vary.
USB cable not included.
Dimensions: 6.5x8.7x2.6cm (2.56x3.42x1.02in)
Notice: Box is custom designed and build with 3D printer. Good quality but not perfect like molded boxes. Please see gallery photos at the top for more detailed view.
Before you order, please read carefully the item's description. Check your radio manual to confirm that is compatible and how to set the correct settings.

• Ship to confirmed addresses.
• First priority shipping next business day with tracking number (You can check shipping date from purchase history).
• Shipping and handling charges covers the real cost for first priority registered post. Shipping with a courier, will be extremely expensive.
• Normally delivered within 5-15 business days after shipping. If you want it very fast, I can not guarantee it, but it will not be unusual, if you receive it in less than 5 days.
• Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast. Also, some countries does not update tracking history, until they deliver the packet.
• I suggest you to use 17track to track your order. If its necessary, choose your destination country.

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.

Check out my other items. Add me to your favorites list.