Universal USB Digi Interface with PTT - PSK,PSK31,RTTY,SSTV

Digital Interface with PTT control
PSK31, PSK, RTTY, SSTV, NBEMS, JT-65, WeatherFax and other digimodes
HF/VHF/UHF(Hardware version 5)

Compatible with ALL radios. Cable include 2 or 4 pairs cable. Make a note when you order, else will be shipped by default 2 pairs cable. Interface is NOT complete finished. You must solder connector(s) to connect it to your radio. I can help you for some radios, but not for all. You must know how finish and connect it. This interface allows your PC or Laptop, to decode/encode digital signals using free (or paid) software.

3 in 1 - BEST VALUE FOR MONEY
USB audio interface + Digital Interface + PTT control
*** sold tens of them ***

• No need to use your PC, Laptop or Netbook soundcard 
• No need to use internal or USB serial port.
  
• No need to plug and unplug your mic & speakers. Just connect it to a free USB port
• No need for drivers
• PnP with Windows XP, Vista, 7, 8 and all OS that support generic audio interface
• Supports FLDIGI, MMSSTV, DIGIPAN, MultiPSK and any other program that can send PTT tone to right audio channel or play the digital signal to both audio channels
  
• You can download software clicking HERE

Why pay more for less? Pay less for more!

HOW TO:

• Fisrt of all you must solder the proper connectors to the end of the cable to able connect it to your radio.
• Connect USB Interface to a free USB port (OS will detect it and install drivers)
• Open your application and configure it to use the proper audio device and select audio mono output or PTT tone to right audio channel. If you can't find such options, probably application sends signal to both audio channels.
• Tune your radio to a digi mode frequency.
• Open USB Audio properties, adjust audio output and MIC level tho the highest level. If it is necessary, disable Mic AGC.
• Plug the connector or connectors to your transceiver.
• Tune your radio to a digi mode frequency.
• Use green potentiometer to adjust audio until you have the proper receiving (RX) level.
• Use red potentiometer to adjust transmitting (TX) level (check ALC level). When transmits, red led turns on.
 

Interface is assembled and tested (except the one end of the cable).
Total interface length with cable is ~1m. Cable, box or jack color could vary.
USB cable not included.
Dimensions: 6.5x8.7x2.6cm (2.56x3.42x1.02in)
Notice: Box is custom designed and build with 3D printer. Good quality but not perfect like molded boxes. Please see gallery photos at the top for more detailed view.
Before you order, please read carefully the item's description. Check your radio manual to confirm that is compatible and how to set the correct settings.

• Ship to confirmed addresses
• First priority shipping next business day with tracking number (You can check shipping date from purchase history).
• Shipping and handling charges covers the real cost for first priority registered post
• Normally delivered within 3-7 business days after shipping
• I suggest you to use 17track to track your order. If its necessary, choose your destination country.
• Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast.
  

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.

Check out my other items. Add me to your favorites list.

Digi Interface with PTT - PSK,PSK31,RTTY,SSTV - Yaesu FT-100,817,857,897,450,950

YAESU
Digital Interface with PTT control
PSK31, PSK, RTTY, SSTV, NBEMS, JT-65, WeatherFax and other digimodes
HF/VHF/UHF(Hardware version 5)

Compatible with Yaesu FT-100, 817, 857, 897, 450, 950, DX1200, DX3000 & FT-7800, 8800 and variations of these models (transceivers not included) and all other radios with mini din 6 pins input/output data port. UniDigi interface allows your PC or Laptop, to decode/encode digital signals using free (or paid) software.

3 in 1 - Best value for money
USB audio interface + Digital Interface + PTT control
*** sold tens of them ***

• No need to use your PC, Laptop or Netbook soundcard 
• No need to use internal or USB serial port.
  
• No need to plug and unplug your mic & speakers. Just connect it to a free USB port
• No need for drivers
• PnP with Windows XP, Vista, 7, 8 and all OS that support generic audio interface
• Supports FLDIGI, MMSSTV, DIGIPAN, MultiPSK and any other program that can send PTT tone to right audio channel or play the digital signal to both audio channels
  
• You can download software clicking HERE
  

Why pay more for less? Pay less for more!

HOW TO:

• Connect UniDigi Interface to a free USB port (OS will detect it and install drivers)
• Plug 6 pin mini-din to Yaesu Data port
• Open your application and configure it to use the proper audio device and select audio mono output or PTT tone to right audio channel. If you can't find such options, probably application sends signal to both audio channels.
• Tune your radio to a digimode frequency
• Open USB Audio properties, adjust audio output and MIC level tho the highest level. If it is necessary, disable Mic AGC. 
• Use green potentiometer to adjust audio until you have the proper receiving (RX) level.
• Open your application and configure it to use the proper audio device
• Tune your radio to a digimode frequency.
• Use red potentiometer to adjust transmitting (TX) level (check ALC level). When transmits, red led turns on.
 

Interface is assembled and tested (except the one end of the cable).
Total interface length with cable is ~1m. Cable, box or jack color could vary.
USB cable not included.
Dimensions: 6.5x8.7x2.6cm (2.56x3.42x1.02in)
Notice: Box is custom designed and build with 3D printer. Good quality but not perfect like molded boxes. Please see gallery photos at the top for more detailed view.
Before you order, please read carefully the item's description. Check your radio manual to confirm that is compatible and how to set the correct settings.

• Ship to confirmed addresses
• First priority shipping next business day with tracking number (You can check shipping date from purchase history).
• Shipping and handling charges covers the real cost for first priority registered post
• Normally delivered within 3-7 business days after shipping
• I suggest you to use 17track to track your order. If its necessary, choose your destination country.
• Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast.
  

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.

Check out my other items. Add me to your favorites list.

Iphone/IPad - Android - Windows, Phone/Tablet, Universal Digi Interface with PTT

 
Universal Digital Iphone/IPad - Android-Windows
RX/TX Interface with PTT control
PSK31, PSK, RTTY, SSTV, NBEMS, JT-65, WeatherFax and other digimodes

HF/VHF/UHF

This interface allows your IPhone, IPad, IPod & Android devices (phone or tablet) to decode/encode Digital mode signals using free (or paid) software. Works with ALL RADIOS. Cable include 2 or 4 pairs cable. Make a note when you order, else will be shipped by default 2 pairs cable. Interface is NOT complete finished. You must solder connector(s) to connect it to your radio.

I can help you for some radios, but not for all. You must know how finish and connect it.

TRRS Jack

Notice: Interface to be compatible with a phone/tablet device, must use a TRRS jack with outputs as shown at the picture. Also, all phone or table headsets to be recognized from the device must have a resistance between Common and Mic Input. The connected resistor to the interface is 1.8K and tested with android/apple phones and tablets.
Interface can recognized from almost any device. To be sure, use an Iphone (4, 5, etc) headset connected to your phone/tablet. If you can talk and listen, then probably you will not have any problem.
For better tune, two potentiometers allows you to adjust in and out audio level.

• Compatible with IPhone, Ipad, Ipod, Android phones or tablets
• Use it with you base or mobile radio 
• Input/output level, can adjusted to use speaker, line, mic, etc.
• Tested with many different brands and models without a problem.
• Supports any digi program written for Apple iOS and Android phones or tablets.

HOW TO:

• Solder connector(s) to the cable. Check manual to find what connectors you need.
• Connect audio jack to the headphone/Mic jack of your phone or tablet.
• Turn on interface (black switch at the left side). A green led opens at the front.
• Tune your radio to a digital mode frequency.
• Lower the transceiver's volume to be sure that phone/tablet does not receive sound from the internal microphone.
• Check if phone volume is full open.
• Use green potentiometer to adjust audio until you have the proper receiving (RX) level.
• Open your application and configure it to use the proper audio device
• Tune your radio to a digimode frequency.
• Use red potentiometer to adjust transmitting (TX) level (check ALC level). When transmits, red led turns on.

Interface is assembled and tested (except the one end of the cable).
Total interface length with cables is ~1.5m. Cable, box or jack color could vary.
9V battery not included.
When is in receive mode, consumption is 6mAh and 11mAh when PTT
Dimensions: 6.2x10.5x25mm (2.44x1.13x0.98in)
Notice: Box is custom designed and build with 3D printer. Good quality but not perfect like molded boxes. Please see gallery photos at the top for more detailed view.
Before you order, please read carefully the item's description. Check your radio manual to confirm that is compatible and how to set the correct settings.

• Ship to confirmed addresses
• First priority shipping next business day with tracking number (You can check shipping date from purchase history).
• Shipping and handling charges covers the real cost for first priority registered post
• Normally delivered within 3-7 business days after shipping
• I suggest you to use 17track to track your order. If its necessary, choose your destination country.
• Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast.

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback.
For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.  

Check out my other items. Add me to your favorites list.

Iphone/IPad - Android - Windows, Phone/Tablet Interface with PTT control (v.6)

Digital Iphone/IPad - Android RX/TX Interface with PTT control
PSK31, PSK, RTTY, SSTV, NBEMS, JT-65, WeatherFax and other digimodes

Mini din 6 pins connector

HF/VHF/UHF

Works with Yaesu FT-100, 817, 857, 897, 450, 950, 7800, 8800, DX1200, DX3000 and variations of these models (transceivers not included) and all other radios with mini din 6 pins input/output data port.

This interface allows your IPhone, IPad, IPod & Android devices (phone or tablet) to decode/encode Digital mode signals using free (or paid) software.

TRRS Jack

Notice: Interface to be compatible with a phone/tablet device, must use a TRRS jack with outputs as shown at the picture. Also, all phone or table headsets to be recognized from the device must have a resistance between Common and Mic Input. The connected resistor to the interface is 1.8K and tested with android/apple phones and tablets. Also can work with windows devices that use same jack.

Interface can recognized from almost any device. To be sure, use an Iphone (4, 5, etc) headset connected to your phone/tablet. If you can talk and listen, then probably you will not have any problem.
For better tune, two potentiometers allows you to adjust in and out audio level.

• Compatible with IPhone, Ipad, Ipod, Android phones or tablets
• Use it with you base or mobile radio
• Tested with many different brands and models without a problem.
• Supports any digi program written for Apple iOS and Android phones or tablets.

HOW TO:

• Plug the 6 pin mini din connector to your radio.
• Connect audio jack to the headphone/Mic jack of your phone or tablet.
• Turn on interface (black switch at the left side). A green led opens at the front.
• Tune your radio to a digital mode frequency.
• Lower the transceiver's volume to be sure that phone/tablet does not receive sound from the internal microphone.

  

  Front side

• Check if phone volume is full open.
• Use green potentiometer to adjust audio until you have the proper receiving (RX) level.
• Open your application and configure it to use the proper audio device
• Tune your radio to a digimode frequency.
• Use red potentiometer to adjust transmitting (TX) level (check ALC level). When transmits, red led turns on.

Interface is assembled and tested.
Total interface length with cables is ~1.5m. Cable, box or jack color could var.
9V battery not included.
When is in receive mode, consumption is 6mAh and 11mAh when PTT
Dimensions: 6.2x10.5x25mm (2.44x1.13x0.98in)
Notice: Box is custom designed and build with 3D printer. Good quality but not perfect like molded boxes. Please see gallery photos at the top for more detailed view.

Before you order, please read carefully the item's description. Check your radio manual to confirm that is compatible and how to set the correct settings.

• Ship to confirmed addresses
• First priority shipping next business day with tracking number (You can check shipping date from purchase history).
• Shipping and handling charges covers the real cost for first priority registered post
• Normally delivered within 3-7 business days after shipping
• I suggest you to use 17track to track your order. If its necessary, choose your destination country.
• Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast.

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback.
For any problem, question, help or if you are not satisfied, contact me (taloseshop[at]gmail.com). I will be glad help to resolve any problem.

Check out my other items. Add me to your favorites list.

Weller WHS40 and WHS40LT soldering iron tip S31

Replacement solder tip 0.4 mm for Weller WHS40 and WHS40LT soldering irons. Excellent quality for long life, S31 equivalent solder iron tip. Item is new and never used.

Ship to confirmed addresses

First priority shipping next business day (You can check shipping date from purchase history).

Shipping and handling charges covers the real cost for first priority post

Normally delivered within 3-7 business days after shipping.

Notice: Delivery to some countries/areas may experience some delay. I am not responsible for that. I ship fast. Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question or if you are not satisfied, contact me. I will be glad help to resolve any problem.

Please remember to leave feedback when you receive and test interface. I ask you to give me positive feedback. For any problem, question or if you are not satisfied, contact me. I will be glad help to resolve any problem.